I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
At what voltage should DCDC be manually turned off for a nRF52832 ?
This thread for nRF51 says:
You must manually disable the DCDC when supply voltage goes below...
Hello,
I followed the steps mentionned in this blog
I did all the required step but I'm still seeing the same behavior.
below is my setup :
I'm using nRF52840 and...
Hi folks,
We got a weird behaviour with our nrf51822(SDK 12.2.0, s130) device. we have built a low power application with following parameters:
MIN_CONN_INTERVAL...
I have tried to understand how data was send from two BLE device. I have had 2 PCA10056 board and I have loaded ble_app_blinky example and ble_app_blinky_c example for each...
Hi All.
I have one question.
I just want to send "volume down key" simplely after connect with android device to take a picture.
I have no idea. and I don't understand...
I modify nrf51 nus in SDK12.3.0 to realize my application, I found when enable uart, the consumption near 830uA , and then call app_uart_close(), the consumption near 5uA;...
Hi,
Is there and C/C++ source code to get float value from 32-bit ieee-11073 FLOAT data type
I need c/c++ code to parse 32-bit ieee-11073 FLOAT data coming from FORA...
Hello,
Using Spi bus with frequency = 4Mbps give me this deformed signals (clock and miso) and when I push it to 8 Mbps I am not able to get the correct values.
Obviously...
When an event is bound to the ppi channel, and this channel is bound to both task_capture and task_clear
can I get the correct COUNT value when an event occurs?
Or can...
Hi all,
I wanna build a IOT gateway. I follow this steps infocenter.nordicsemi.com/index.jsp
When I access coap://[ipv6] It dont have resource light, just only have...
[SDK 12.3.0 / nrf52 DK / Keil tool / beacon example code]
Hello. i am a novice developer.
Power On - Beacon data transmit and enter to sleep mode after 10 sec
...
I fail to integrate “ble_app_multilink_central” and the uart portion of “ble_app_uart_c”
I have checked other posts and it is inconclusive if and how they got the integration...
In traditional approach to ESB communication we have many PTX device and one PRX device:
In my application, situation is inverted: I have only one PTX device and many...
The function peers_id_keys_get() (SDK 12.3.0 Library id_manager.c) returns Error BLE_ERROR_GAP_INVALID_BLE_ADDR (0x3202) when the peer device address is neither PUBLIC nor...
