My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hi there,
I attempted to change the nRF54L15-PDK settings in Board Configurator. I disabled VCOM0, VCOM1, Power to LEDs, Software Debugger and set VDD to 2.0V. I have...
Hi all,
I am working on nRF-9160 and nRF-9151, and I wanna know does Serial LTE Modem support will message function for MQTT connection or other connection?
I've asked...
Hi,
I am not familiar with the 9160DK board. I followed the same steps as the nRF Desktop Connect application guide but it always shows verification failed. I am using my...
Hi
I'm having an intermittent connectivity issue with the nRF9161 where after days of operation the device loses cellular registration and fails to reconnect.
The...
Hi,
is there a way to hide the west project from the Git view in VS code? Sometimes you just don't need to view any changes related to west and it's getting quite messy...
I am working on a Zigbee network using the nRF Connect SDK and need to retrieve the link quality information (LQI) of a specific device based on its short address. What ZDO...
Hi,
I have used nordic documentation a lot few years ago, and I am looking for BLE sequence diagrams especially the ones during pairing process with LE Secure connection...
Good morning,
currently we are on ncs SDK v2.7.0.
Because SDK v2.8.0 supports the KMU in MCUboot on the nRF54L15, I updated immediately and gave it a try.
Unfortunately...
Hello,
I searched but I can't find how to retrieve accelerometer data with thingy:53 and then send it via bluetooth to nRF Connect on phone?
Can you help me
Thank...
Hi,
I have opened sample "Peripheral_hr_coded". I have build it successfully. I click on debug. I expect cursor would start from Main function. But Debug was not started...
I'm developing my application using the NRF Connect SDK in VS code. SDK Version 2.4.2. The NRF52832f we're using is integrated into a module made by fanstel and it has been...
Hi,
I am going through the DevAcademy Bluetooth LE lessons, using nRF5 DK. But I run into problems directly in the exercise of the first lesson. Everything goes fine to...
Hello Nordic community,
I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
I want to use a switch in the overlay file, like:
To do so, I try to add a config statement in a custom KConfig file. (mp_Kconfig.conf):
Adding the file to the build configuration...
Hi,
We have come to expect that with the nRF Connect SDK installed properly and using recommended options we can build a sample, for example
$cd \ncs\v2.8.0\nrf\samples...
