I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I followed Einar's nRF52840 Dongle Programming Tutorial and tried the ble_peripheral/ble_app_eddystone example using SES 4.12. Opened the project, changed the preprocessor...
Hello All,
I have been using this NRF52 DK board with KEIL for like 2 weeks. I read the all the document regarding BLE 5 protocol and followed the DIY codes step by step...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
Hi,
I referred uart example in nRF SDK 15.0.0 and tried to implement on proxy_client program by adding all files which there in example. but still i'm facing compilation...
Hello!
I'm facing some problems when I try to broadcast a message from my receptor to the transmitters, I'm using 3 nRF24L01P. I read some things about setting the same...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
I want to use application board and connectivity board with mesh sdk in nordic chip. Is there serialization is available for mesh like using in nRF SDK15.0.0 peripheral driver...
We are developing an application on the nRF52840 kit with SDK 15.2. We are using Keil as compiler. I have started developmet my application with the example ble_app_cscs....
Hi,
I would like to try the DK in a high voltage mode. I tried switching the power source switch to either LIPO or USB (using LIPO battery and USB respectively) but in vain...
Hi, I'm new to thingy, I want to log the data received and viewed in mobile app / web app from thingy 52 development kit which contains nRF52832. Is it possible to log data...
Hello everyone,
I am in trouble because of a vlotage of current problem, I think it is most a voltage problem.
Let me explain,
I have a NRF51DK that I programmed to...
