Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi, we are looking into the Nordic tool chain (esp. for uRF9160) integration to Visual Studio Code.
We found PlatformIO has the extension. However it only supports uRF51...
Hello I have tested the example "ble_thread_dyn_mtd_coap_cli" from "nRF5_SDK_for_Thread_v0.11.0_84a130f" : this example works fine for a PCA10056 but I'd to test it on a PCA10059...
Hello community
In the pin_change_int example the following code is written:
So, this basically means: whenever PIN_IN goes from low to high, the 'in_pin_handler'...
Hello,
There is a comment in the v1.1 manual (shown below) which states that the first capacitor in the matching network (C3 in the reference designs) shouldn't be connected...
Hi:
By our stack up at Z direction, there is a touch sensor FPC coil above nRF52840 and the gap is 0.65mm
And this coil will radiate about 1xMHz radiation
Will it impact...
Looking for different options for flashing/dumping program on custom nrf52832 pcb designed and used as BLE.
Has another full fledged MCU on PCB which handles all the peripherals...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
I have my Thingy:91 working now but I can only see "terminal" data in nRF Connect for Cloud. I was expecting to see graphs of the data and a map when I have a GPS fix. The...
Hello everyone,
I am using light_switch server and client example from nrfmesh examples but nrfmesh ios application cant find nrf52 usb dongle.
I have changed pca10059...
I have developed USB firmware for the 840 based on the USBD example so that we can use WINUSB (WCID) for the host. The design is for USB 2.0 full speed with EPIN1 for device...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
Somehow my account got deleted and so did my ticket. I had to re-register my account an i'm creating this ticket again:
nrf9160_pca10090ns.dts.pre.tmp:89.42-101.3: Warning...
Your served radio tramsmitter/receiver example using PCA 10000 USB dongle, PCA 10001 evaluation kit.
It's just only one byte data communication. It works well.
If I communication...
