I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I am developing using the nRF5340DK with Segger v5.68 and SDK within toolchain v1.9.1. My project works perfectly on my old PC, but after moving to a new PC with the exact...
Hello, I would like to implement a simple RSSI-based distance measurement function using the Periodic Advertising Samples（periodic_adv & periodic_sync）. In the scan callback...
Hi,
I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
I don't know who's in charge of Dev Academy, but the nRF Connect SDK Intermediate Lesson 9 -- Bootloaderse and DFU/FOTA section looks like it was written as a back burner...
Hello, I am trying to save some sensor data based on my current state of the device. I want to log IMU data and timestamp into my external flash (MX25R64) with littlefs file...
I am using a custom board with an nRF52840. For OTA updates, I’m using SDK 17.1.0 based on the sample codes:
Bootloader : secure_bootloader
Application : A custom...
I am developing with thingy53. I would like to enable BLE function, MCUboot and littlefs file system at the same time. I am using SDK and toolchain v2.7.0 and sysbuild as...
Hello, I’m testing a circuit built with the nPM1300. When connecting or disconnecting power via USB-C, noise is generated at the circuit's button, causing unintended signals...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
The samples "nrfx_gppi/fork" and "nrfx_gppi/one_to_one" are both broken and fail to compile. I have confirmed this for NCS 2.8.0 and 2.9.1 on Linux, and 2.8.0 on Windows....
I am currently developing firmware on Qorvo's DWM3001C module , which integrates the Nordic nRF52833 . I am using nRF5 SDK 17.1.0 and the SoftDevice S140 .
My base project...
Dear nordic team,
even if enabled for mcuboot via CONFIG_WATCHDOG / CONFIG_BOOT_WATCHDOG_FEED, our device performs a reset when swapping the image. More precisely: when...
Hello,
As I understand, the nRF54L15 have pins dedicated for clock functionality.
They are marked red in figure 165 ( page 796) of the preliminary datasheet, rev. 0.8...
When I build my first blinky sample, I met a error and correct it with ( https://devzone.nordicsemi.com/f/nordic-q-a/120279/update-to-ncs2-9-1-compilation-error/529668) ....
