Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi，
When I used NCS V2.5.0,after two devices successfully establish a BLE connection but then disconnect due to a timeout, subsequent reconnection attempts fail with error...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hi all,
I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem.
The red area is the data I sent, but the blue area is not what I sent....
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hi,
I'm trying to test DTM over USB CDC with an nRF5340DK unfortunately, Direct Test Mode desktop App is not detecting the DK.
Build command (copied from VSCode output...
Hey folks,
i have to use the nrf9160 board to create a PoC for a project of our company. The main topic of the PoC is not important here because i cant even connect to an...
Hi,
We are on NCS v2.9.1
We have an existing project on based on the nrf52832, which we use as a hci_spi controller. There, CONFIG_BT_LL_SW_SPLIT is set. We are now porting...
Hi, I have encountered issues flashing a NRF52833 board which is on a custom PCB. I have picked the project up from another developer so it is somewhat developed already....
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
hi support team,
i want to confirm the FEM control when using nrf21540ek for mesh demo "light" with 52840dk.
i set :
CONFIG_BT_CTLR_TX_PWR_ANTENNA =20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB...
Hello Team,
I am trying to set configurations for FOTA. I refer smv_server sample code and the following document https://docs.nordicsemi.com/bundle/ncslatest/page/nrf/app_dev...
We are using the NRF9151 and unable to establish a connection to an LTE-M network in Ireland (testing in Cork currently). We are using a Kore MVNO SIM which supports Three...
Hi,
I am trying to upload data from two sensors, the BME280 and APDS9960, to the nRF Cloud. I have been able to extract data from the sensors with I2C, but it seems I am...
Hello,
I am developing a new application using nRF52832 and writing and debugging code on Segger embedded studio (Release 5.68) with SDK v17.1.0.
I try to run simple application...
Hi,
We have implemented a custom attribute reporting function based on IasZone. However, there is a very long delay in reporting device attributes, which may range from...
