Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello.
I am developing device using nRF52840 and i have question about IO pin usage.
The circuit is currently providing voltage to the A12 pin (Digital I/O), but it is...
Hello,
How can I handle multiple peripheral connections to one central instead of stopping scanning upon the first connection (ex: multiple heart rate sensors communicating...
hello
I am studying DFU with reference to the Academy.
Exercise 1 - DFU over UART - Nordic Developer Academy (nordicsemi.com)
SampleCode of Exercise1 use McuBoot and...
Hello,
I want to use McuBoot so I added CONFIG_BOOTLOADER_MCUBOOT =y to prj.conf.
So t here were a lot of warnings "implicit declaration of function ".
Part of the warning...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using NUS to work with...
I need to use 9160 to drive the Lis2dw12 accelerometer for ST. I found some settings related to this accelerometer in NCS, but I couldn't use it after adding it in IIC, and...
I am having trouble understanding how to measure the power consumption of the nRF9161DK as recommended by the documentation: https://docs.nordicsemi.com/bundle/ug_nrf9161_dk...
I need to use UART0 of the nRF9161 via Tx(P0.27) and Rx(P0.26) for serial communication. There is no CTS/RTS signal.
I used the code from Lesson 5 of the DevAcademy. i...
Hi, I have an issue I can't understand. I'm getting the TRICKLETIMEOUT (Trickle timer timeout) ERROR 64 from my nPM1300.
If I understand correctly:
1. Trickle charging...
I am using nRF52832 for high-rate sensor.
Of course, I can use SPI using CPU but it's busy for other jobs.
So I want to use DMA if it's possible.
Currently I am using...
Hi There,
Our peripheral firmware running nrf5 cannot seem to connect properly to our central running NCS 2.4.1 over BLE. We are consciously setting the connection to use...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
I 'm using zephyr to create a custom nrf52832 board .
I 'm using the Devicetree Visual Editor .
Any idea why I can 't select this specific display controller ?
The datasheet...
Dear Nordic Support-Team,
the provided samples in nrf-SDK are great to show how to use several aspects of the nrf Sdk and the devices.
Nevertheless it would be great if...