Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
We are working on our manufacturing process that involves use of the nRF9160. I need a way to programmatically get the IMEI and ICCID in order to register the device...
I'm running a nRF52 device that's built on nRF5 SDK11, and it's remaining that way now due to regulatory reasons. My application needed to be updated to support bonding, and...
I have a nRF9160DK board running asset_tracker_v2 on a nRF9160 custom board. V1.7.0 loads and boots fine but when I use V2.5.0 the boot fails as shown below. The only change...
Hello, per the product specification, I see that the nRF52832 CIAA variant requires a shunt 1.0pF capacitor and series 3.3nH inductor.
Is this recommended regardless of...
Hello,
first I would like to "set the scene".
* hardware : cutsom board
* mcu : nrf52832
* nRF5_SDK : nRF5_SDK_17.0.2_d674dde
* software : mbr + bootloader + softdevice...
I have configured NRF52840 as coordinator ,EFR1 (ENDDEVICE) and EFR2(ENDDEVICE) as end devices. These 3 devices are connected in network.EFR2(End device )continuously sending...
I would like to understand the issue of frequency offset calibration in RF signals, I have viewed the
Case ID: 309794
nwp_006.pdf
I would like to know if I can do...
Hi,
We are working on BLE MESH using nRF52840. We are trying to put nRF52840 into deep sleep mode. The deep sleep current is about 210 micro Amp. Further, the current is...
Hi,
I have a coap server/client system and when I send a provisioning request from the client I can see the server is sending the reply. But my 'on_provisioning_reply (...
Hi,
I'm using SPI4M on nRF53 and came across it's errata, but I didn't get where to call the workaround functions.
The workaround is to call the below line upon enabling...
Hi I have a mbed application, which runs on a PSOC6 MCU, i am going to be using a fanstel BC832 (which is based of NRF52832)BT module for RF-communication. To verify that...
I have a custom board with an nRF5340 on it. I'd like to offload BLE operations to the network core using the RPC library to control it from the application core.
The documentation...
Quick Background
The spi_transceive_cb() function in Zephyr takes two buffer sets (among other arguments). One buffer set to TX and one buffer set to RX. You may pass NULL...
I have found a bug in SDK v2.6.0 at zephyr/drivers/flash/nrf_qspi_nor.c while erasing the external MX25R64 flash.
Environment:
nRF5340 DK Hardware (MX25R64 external...
Dear All,
We want to test the maximum distance of Broadcast audio gateway using nrf21540EK with nrf5340 Audio DK.
And we want to output the rssi info periodically on the...