Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
The question is, is it possible to GATT communicate with each of the multiple...
HI
I am traying to convert library max30105 arduito to Nrf52840 code but i have a problem about this
I am reading de Reg FIFO led red and led IR , but its not the same...
Hi I'm currently using the sample py script which is given in https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nordic-thingy52-raspberry-pi-python-interface...
Hello Nordic Team!
I'm working with the nRF52832 and following this tutorial from Nordic to do OTA DFU: https://devzone.nordicsemi.com/guides/short-range-guides/b/software...
OpenThread and MCUBoot don't play well together anymore of the nRF5340 with the release 1.8 of the nRF Connect SDK. Flashing :
results in the bootloop with I assume is...
Hello,
I am a beginner in nRF. I want to implement EEPROM. So I am trying to execute Zephyr/sample/driver/EEPROM code but I am getting compilation error the below error...
Hello,
I am new to BLE. I am currently working on a beacon application. I have used the beacon example code from SDK and modified it. I am using SDK-17.1.0 controller is...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to simultaneously send advertisements with different cycles, communication packets, etc.? If so...
I've been tinkering with my Dev Kits (3 @ nrf52840-dk and 1 @ nrf5340-dk) as I try to find the right software/hardware architecture for my use case.
I made a lot of progress...
Hello , i am developing drivers for a spi ic , which by using spi example i wrote the drivers they are working fine , also i am able to run and modify ble uart example according...
Hello Sirs
I am using the NRF3540-DK development board to program an external NRF5340 chip. I have connected the RESET,SWDCLK,SWDIO,GND,3V pins of P20 connector on development...
I need to connect a ble device to a double uart0 and Uart1 over zephyr.
The first uart in used for comunication puupose e message everty 20mS at 115200;
The second uart...
I'm trying meshdfu. Use 52832 to DFU a lantern program according to the official routine. After success, the program can run, but it can't run after DFU with 52840. Here's...
Hi,
I'm trying to build the blinky example for the nRF5340 network processor with the empty_app_core as a child image for the application processor and get a fatal error...
Hi ,
I have the nordic nRF9160 DK and the Nordic Thingy:91. I am trying with the Asset Tracking application version : nrf9160dk_fw_2021-12-15_cfedfdfa, with the last modem...
