I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I am using nrf52832 board sdk vr 17 s132 soft device. I want to have a way by which i can reduce the brightness of led while it blinks during advertising mode using PWM. pls...
Setup mcuboot and dfu to upgrade firmware on the nRF52840 of our board. Upgrading to new firmware works as expected and the new firmware is running after the install. If I...
Hi，
I am using nrf52832+freertos to develop a low-power product based on the example(ble_app_hrs_freertos) in the SDK, but now I find that the power consumption far exceeds...
Hello Nordic! I have connected a sensor to the DK via SPI. It outputs a lot of data, a lot... for 1 second of data I get 4096 entries. Each entry is 10 bytes in length.
...
I'm working on a design featuring two different MCUs. I'm looking to use the nRF52840 as one of them. I need both processors to be able to send each other messages and ideally...
Hi,
I have a weird problem. My application starts two timers, one after another. Like this:
Normally it just works - no errors, nothing. However, after a DFU OTA upgrade...
What is the best method to store TLS certificates on the nRF5340? I have seen 2 options, but I'm not sure what is best practice and what does work.
If I store the certificate...
Hi,
i just got my hands on Thingy 52, just want to know how do i get started in retrieving data from it, specifically for motion(accelerometer data), if someone can point...
Hi,
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple of weeks, explored almost the whole devzone, learned a...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
HI,
I need to check the following thing with you. I need to use an I2S mic with NRF5340 between the mic and the controller we need to place 2meters of wire. So, I need...
Hello All, I'm currently working on an application with a central and peripheral devices both using nrf52832 with SDK 15.3 and S132. I'd like for the central to be only trying...
Hi Nordic Team,
My dev environment is as follow:
nRF52832(Ble Central + nfc) + S132+ SES
I have integrated BLE Central Multilink uart project with nfc writable ndef...
Hi Devzone,
A couple of conceptual questions about what is possible and a request for ideas for how to best accomplish my goal.
I want to implement a command line...
