I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi,
nrf52833 custom board
My query is that how to do OTA DFU on ble central devices (we are using nrf52833 as receiver dongle(ble central) device)? Does anyone advice...
Hi all,
when I follow the blog as below, find the actual output is not same as expected.
Adding a Peripheral to an NCS Zephyr project - Peripherals And RF Test - nRF Connect...
Hi Everyone,
I recently purchased the NRF52840 DK with a PCA10056 designation. I connected the DK to my Windows 7 laptop via the USB. This resulted in the JLINK(D:) drive...
I have a custom board with a nRF52805 module but I don't understand how the SDK works.
I followed some guide to simulate nRF52805 software, I had to patch some files in...
Hello,
I add sd_ble_gap_phy_update() in the ble_evt_handler() as below:
case BLE_GAP_EVT_CONNECTED: { ...... ble_gap_phys_t const phys = { .rx_phys = BLE_GAP_PHY_2MBPS...
The CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING=y Kconfig option causes kernel booting to hang at line 505 of clock_control_nrf.c.
This is on the v1.7-branch of NCS ...
I have created a custom board containing the nRF52832. I have two copies. The first board works, meaning that I have flashed the code to it using the DK52, and I can power...
Hello,
I have been evaluating the nrf9160 DK board. And my application is using mbedtls (vanilla) and TFM (Used https_client as a starter project). The problem is that with...
Hi,
I'm new to nRF/Zephyr development and trying to integrate the OV7670 camera with the nRF52840 board. Since there was no driver for this particular camera I ported the...
I'm having a problem with what should be a very simple exercise. I'm trying to compile the Zephyr sample subsys/cpp/cpp_synchronization after adding #include <string> to the...
Hello,
I am trying to read data from LS2DE12 accelerometer MEMS chip via I2C bus and I am seeing only zeros for all 3 axes.
I can write to the various registers successfully...
Hello, I ran the nrfconnect (ver 3.7.1) in Power Profiler (ver 3.1.3) in BLE advertising.
When I run the source mode on 3000V I get normal peaks (20mA), however when I run...
Hi,
I'm interested to use AGPS in my project. Looking into AGPS example (link below) , I want to prevent using low power mode since as far as I know using this command you...
Power Profiler software returns an error after I updated it to v3.2.0 with nRfConnect v3.8.0.
Error message: Error while probing devices: EnumerateWorker json error
Resulting...
