Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I am running the demo about knx iot. (branch: v0.3.0_rc in https://github.com/NordicPlayground/nrf-knx-iot )
I build and run "light_switch_sensor" and "light_switch_actuator...
basically, I want to use dm feature in connection-oriented communication. not in connection less, and I want to connect 1 central to 4 peripheral and measure distance.
Can...
nRF Conncet for Desktop v5.0.0
Hello,
I have some trouble to update the Toolchain Manager of version later than v1.2.6. The download fails. However, I can download the...
Hi,
We are working on a project using the nRF52832, which utilizes UART for a QR-code sensor, I2C for an OLED display, and SPI for external flash memory.
We are at the...
Hello.
I am trying to write protect the Flash area using nrf52840's ACL peripheral. I tried to perform the same process on the main processing side by referring to nrf_bootloader_flash_protect...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. Can I advertise a special data? like 0x08,0xff,0xa6,0x02,0x33,0x09,0x55,0x00,0x0c. 0x08 is packet...
I am looking for to buy(I don´t have a 3D printer) a enclosure to protect my nRF52840-DK. It is not a good practice to handle because probably soon this practice will damage...
Hello, I just receive a nRF9161 Development kit and I'm completely new to both nRF9161 and Zephyr.
I want to start an evaluation project based on the nrf9161 lwm2m client...
Hi
I'm chnaging the Secure Bootloader to an external falsh for bank1, connected with QSPI.
In the function on_data_obj_write_request is the call for nrf_dfu_flash_store...
Setup:
windows 11
VS studio code
Toolchain and SDK v2.6.1
hardware: nRF52840DK / PCA10056 (bought June 2024)
Using sdk/zigbee-Template as the base for the project...