Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Link: https://www.nordicsemi.com/Products/Development-software/nRF5-SDK/Download#infotabs
Clicking "Download files" at the bottom, eg with SDK 7.1.0 selected causes a...
Hi,
I want to configure the bootloader (MCUBoot on a nrf9160) to reject a new firmware image update if the new image is not suitable for the current hardware (e.g. multiple...
Hi Dev team,
I have my Thingy91 deployed and running. I wanted to know how could I locate the base station that my device is connected to. I have the information of MCC...
Hello, i'am trying to display data on my sensor Bme280 aka (temp, humidity and pression but the build is successful and the jlink is well connected the wiring is like below...
Hi,
I was using nRF Connect with all applications listed. But after installing nrfutil from git, the application all disappeared. I uninstalled nRF Connect and reinstall...
Hi, I'm attempting to use an nRF21540 to boost the range of a BLE Beacon, and I'm running into a lot of trouble getting the Eval/Dev Kit set up. First off, is there any documentation...
Is there an nRF Connect mesh sensor example. The light on/off example is great, but very simple. There is an nRF5-SDK-for-Mesh example. Are nRF5-SDK and nRF Connect compatible...
Hi to everyone,
I'm evaluating an application consisting of a bluetooth mesh where each node sends a status message to the others.
The area where the nodes will be deployed...
Hi,
We need to know the list of models (like health, configuration, lighting, sensor, generic on/off) in nCS sdk 1.7.0
can you please share inputs
thank you,
To update the Application, it is necessary to implement the update via CAN bus. Below is the hardware part, we use a CAN-SPI chip to access the bus.
We´ra using Microchip...
I would like to disable completely the 2.4Ghz radio after the 52840 has full soft device enabled and ble stack has been run.
This is after the full sequence of bluetooth...
Hi Devzone:
We put the radio test project on our custom battery powered board and encountered a problem.
When we disconnect the usb cable, the tone emitted by radio test...
Hello,
we developed the battery management system with a NRF52810.
Now the product is passing different certifications.
We need to provide info to the certification...
Hi
Trying to implement Full modem firmware update over serial port (USB) on nrf9160 in accordance with nrf\samples\nrf9160\fmfu_smp_svr in ncs version 1.5.1.
It seems...
Module: nRF52810
SDK: 14.2
Softdevice: S132 v5.1.0
Hi,
I modified the serial dfu bootloader exemple to use the SPI slave 0 instead of the UART to communicate between...
