Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports Dual Bank DFU. This limits...
Hi Team,
We are using the nRF52840 for our development purpose. For sake Cyber security purpose we need to disable the Jtag debug port.
For this we have used the below...
Hi Team,
We have seen 10 instances in past 2 months where customer mobile phones failed to discover BLE device. This has happened 8 times with Moto G7 power (Android) and...
We have a module based on the nRF52840, today we loaded the pre-compiled hex file for the BLE DTM code to 2 nRF52840-based modules and noticed when using the nRF connect DTM...
Hi !
I want to whiten the BLE Advertising data(channel 37,38,39), but I don't know how to do it.
I tried many things, but nothing worked.I'm on 52832 platform Flash_S132_NRF52_7...
Hello,
I have got three nRF52840 Dongles to test Bluetooth mesh. I have been going through the devzone queries and found that many people have previously asked about SDK...
Hello,
I am using the nRF52832 with the s132 SoftDevice. I've been trying to interface the VL53L0X sensor to get ToF readings. I'm using the code of this driver . When calling...
Greetings!
I am using NCS 1.4.99. I have spent some time debugging my I2c application on NRF5340 and I came to the realisation that I was not able to control any pin that...
Hi,
I'm developing a program using SPIM instance 1 on nRF5340 PDK, with nRF Connect SDK 1.4.0.
The problem I met is exactly the same as this post . If I want to use a...
NRF52832, nRF52840 is under consideration for development. Because of the implementation of Secure Boot and Secure Key Storage capabilities, we want to choose the nRF52840...
Hi,
I was able to upload a binary file before, but not able to upload a binary file to nRF connect app in order to FOTA.
Could you please help me to upload a binary file...
I am trying to compile and run the ble_app_hrs example for an nRF52810 dev board, using Segger Embedded Studio v5.34. I am using nRF5_SDK_17.0.2_d674dde, with s132. This is...
Hi,
I am looking for a working example for upgrading the MCUBoot itself when we have the configuration B0+MCUBoot+APP, especially wrt to SLM application.
I have gone through...
Hi, I am developing using Segger Embedded Studio.
I downloaded the module and checked that output/debug/Exe has a .hex file.
Then can I download this output file back...
