Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I have an application where I would like to use ACLK at 12.0 MHz to drive the I2S MCLK signal and create an atypical audio sampling rate (46875 samples/sec). If ACLK is at...
Hello!
Using SDK v2.6.1 and the nRF5340 Audio application, I want to use an external button as button5 instead of the one that is on the board.
I noticed that if i change...
Sometimes I just want to compile a single file for an nRF Connect project with VS Code and the nRF Connect extension. This sometimes fails because an include file isn't found...
Hi.
I am updating an nrf9160 B1 project on a custom board in SDK 2.1.0 to SDK 2.5.3, and I am running into a problem when building. This error does not show up when building...
Hi,
Hello, I have a project that's working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a so many threads on this...
Hi DevZone!
I'm currently developing a device that has several hardware actuators and I've implemented 2 OnOff Models each belonging to an element. But right now I'm having...
Hello there!
I'm trying to enable secure boot via CONFIG_SECURE_BOOT and am currently getting the following error:
I'm using zephyr via sdk-nrf v2.6.1
Searching the...
Hi,
I just try to use the DFU over USB to upgrade the FW but i found one problem which is the process will erase the external flash data
but i put the some sensor FW data...
I'm upgrading from SDK version v2.4 to v2.7 which introduces the new Zephyr hardware model and I'm struggling with the transition. I have two custom revisions is based off...
Hello,
I am using nrf7002dk on NCS version 2.6.0.
I want to send data to an HTTPS web server using WiFi.
I saw some mentions about HTTPS in several posts on Devzone...
HW/SW Versions:
nrf52840 Dongle DK
nrf Connect SDK 2.5.2
Issue:
I'm developing a Zigbee device based on the ZBOSS, using an nrf52840 dongle development kit and there...
Hi,
We have developed a nrf5340 custom board powered 1.8 V. So we cannot use the nordic DK board to program it.
I would like to know if there is an interface other than...
I have an application where I am using the SAADC to take ADC samples. At any point during the measurements, I want to be able to stop the samples prior to the ADC buffer filling...
Hi,
I trying to adapt the ble_app_multilink_central example to allow more than 8 peripheral connections to the central device. However, when I change NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am using nRF52832 board and I want to understand the current consumption in the board will differs while running the code in zephyr RTOS platform and without zephyr...
