Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I have a project using nRF Connect SDK v1.9.1 and recently started having the issue that when I build it in VS Code with the plugin it always asks me to do a Pristine Build...
I upgraded from v2.7.0 to v2.8.0 of the nRF Connect SDK and noticed that the UART was no longer working.
It seemed the UART receives one byte and calls exit. Transmit doesn...
Hello, we have a following issue: we would like to use nRF5340 QSPI driver with external RAM to store measurements data. Power supply for PCB is 1,8V, so we tried to use APS6404L...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hello,
Currently, I am working on the nRF 52840 DK and the UART port named uart0 is connected to the on board debugger, Where do i find the pins for the UART1 ? I could...
Can Channel Sounding technology and BLE Mesh be used at the same time? Does the SDK support it? If they can be used at the same time, will it affect the communication of mesh...
I work NCS2.8.0.
In NCS2.6.0, there was no problem if I put the BOARD settings in CMakeLists.txt and ran "west build".
However, in NCS2.8.0, an error occurs. (undefined...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
Hello,
I am looking for information to be able to process CI/CD automatic tests for an nRF5340 project.
I mean compilation of the project, and simple tests by using GitLab...
Hello,
I am using NCS v2.8.0.
In this, when I configured the application to use OOB legacy pairing only mode, the build process failed.
Following is the configuration...
Now I want a packet (8 bytes) to be sent out at 8k, but now it is only about 5k, I did not set the ack, is there a way to verify that the ack reaches 8k,The library currently...
Issue: I am trying to flash the zephyr sample code into custom board with nrf52840 chip. I am frequently getting the recovery failed error or the JLinkARM DLL error. I have...
Hi everyone!
I'm having trouble getting a custom PCB with the nRF52832 chip to work, specifically with enabling BLE functionality.
It seems there are issues related to...
