Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
I am trying to interface an SD card over SPI on nRF54L15 using nRF Connect SDK .
I started from Nordic’s fs_sample , which by default uses SPIM20 on Port 1 pins , and this...
I am using SEGGER Embedded Studio v8.26 with J-Link software v8.94 on Windows (64-bit) for BLE development on the nRF52840 DK .
Using J-Link Commander , I am able to:
...
After upgrading my NCS version from 3.1.1 to 3.2.0 for the nRF54L15, I found that the GRTC resets after a sys_reboot(), whereas it didn't in the previous version. What changes...
Hello everyone. I'm using the nRF52840 Pro Micro board with the J-Link programmer and the nRF Connect extension for VS Code. This board comes with a U2F bootloader, but I...
I use a hardware timer to capture/compare incoming pulses using PPI to trigger the captures from GPIOTE. I previously wrote the same application for nRF52832 on the old SDK...
When running SLM on nrf91, it sends "Ready\r\n" over UART on boot/reset. On nrf54, we use "Ready" to detect reboots and rerun the setup. However, when the modem reboots, sometimes...
Hello Team,
I am using the nrf54l15 custom board for development. I have configured the P1.06 as a normal GPIO as follows:
And using it as follows:
The pin status...
I use example from nrf52 SDK. project path:nRF5 SDK\nRF5_SDK17.1\examples\ble_peripheral\ble_app_uart\pca10040e\s112\arm5_no_packs.
emulator: ST link V2
but no target...
Hello,
The nRF5340 supports audio transmission, while the nRF54L15 supports Channel Sounding. Is it possible to conduct audio transmission simultaneously with Channel Sounding...
We need to use a Lithium Ion battery to power our device and need to connect to a chip that has 1V8 logic levels as its only option.
We're early in development, so it seems...
I am encountering a strange hardware/software mapping issue with the SAADC on an nRF52833 DK running on Zephyr (NCS) . Using VS Code nRF Toolchain and SDK (V3.2)
The issue...
This one gets complicated as I cannot reproduce the problem with my original NRF5340 DK.
Steps to reproduce are trivially easy, but only fail when using my favourite OEM...
Just a quick one as I couldn't find it on google. I'm going to implement a beacon like broadcaster but one not based on location. It'll probably be a uuid, a random identifier...
Hello,
I encountered a problem while trying to bond a nrf54L15 (central) with a nrf52810 (peripheral). The firmware of the nrf54 is using Nordic Connect SDK and the nrf52...
Hello,
I hope you are well.
I have a code inside the connection connected callback that sets the MTU to the maximum, which is working fine on ncs v3.0.2 but generates...
