I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi,
NCS for Windows VSCode have update to last,
TERMINAL panel can't copy one line,
and can't clear all.
Suggestions for improvement.
thanks
Best Regards
Toolchain: 1.9.1
modem fw: mfw_1.3.1
PC OS: windows 10
Terminal software: Tera Term
SIM card: AT&T (North America)
in the modem shell example code, in "prj.conf...
There are multiple issues like https://devzone.nordicsemi.com/f/nordic-q-a/81793/jlinkarm-dll-load-failed-on-m1-mac which are basically just « resolved » by saying « these...
Hello,
I'm trying to figure out what I am doing wrong (or what I misunderstood) about the bitrate.
According to my benchmark, it takes 1.42ms to send 128 bytes using ESB...
Hello, I'm using SFH 7072 Heart rate sensor with nRF52832 board , But i'm not getting actually heartrate, i'm getting like a 6-7 digit output , for that which calculation...
It is written in the datasheet that if i try to receive bytes more than the number i put in the maxrx register "incoming bytes will be discarded" does that mean all the bytes...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a
In my application i need to read characteristics value, so after following tutorial...
i use the zephyr 3.0.9.i use direction with nrf52833 or nrf5340 in RX.The tx is nrf52833 with nrf of NCS,ITversion is zephyr 2.7.9.The default is 2us AOA. I want to use 1us...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hello,
I have been working with a BLE custom board project for a few months and the product requires buttonless DFU feature. The bootloader that I initially used was derived...
System details:
Board: Custom
Chip: nRF52832
PCA Number: PCA10040
SoftDevice: S132
SDK: Version 16.0.0
I have been building a custom nRF52832 device for a...
I'm trying to use the LTE Link Monitor, but when I open the app, the log shows: Failed to get the library versions: JLINKARM_DLL_COULD_NOT_BE_OPENED (Origin: "Failed to get...
sdk: 1.6
modem fw: 1.2.3
Hi,
Been trying to test mqtt every which way and not getting any success with mqtt keep alive longer than 30 minutes, the mqtt connection...
Hi All,
I have encrypted app_update.bin manually and perform FOTA with single stage bootloader and it is working as expected.
Now I have enabled Two stage bootloader...
i am working with spi example but the clock appears as shown in the following photo i do not know why it is generated like this and i need help to configure it to work as...
