Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi, dear Nordic & all：
When I run libuarte example，I found a problem， I just set P0.14 to high at the begin of mian function, then I send data and test the example's function...
Hello,
I'm trying to develop an application sending GPS over HTTP requests.
I started from the "https client" and "agps" samples in the NRF Connect SDK: the single examples...
Hi,
I'm trying to build secure bootloader DFU(non_debug_version) for PCA10040 with the below mentioned prerequisites and I'm able to build the bootloader successfully...
Hello,
I am using nrf52832 chip and SDK 17.0.2 (Softdevice 7.2.0).
I set the MAC Address as random static as shown below (only relevant parts shown):
ble_gap_addr_t...
We are an educational institution and were hoping to use these in a class integrated with LabVIEW. When we load this up on a faculty desktop and run a simple program, it works...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. Is it possible to connect two centrals at the same time? I think peripherals can only...
What exactly does the power management library? Does it handles all the ongoing processes and shut them down?
Because I did a test with for instance a flash write, and I...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
Hi All,
I am developing one device using nRF52840 based on Zigbee protocol.
Currently I am using nRF52840 Dev-kit and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
...
Hello,
as discussed in the email with Joakim T., could you please provide us a sample of how to use AT command %KEYGEN to generate CSR using the ECC private key? If you...
I am using NRF52840 with SDK15
I am using AES 128 Encryption and am confused on the documentation:
During the encryption operation with nrf_crypto_aes_crypt or nrf_crypto_aes_finalize...
Hello everybody,
I'm currently trying to create a Bluetooth Low Energy Mesh network of multiple nodes that I can control using a Bridge application.
I use a nRF52840...
Hi,
we are developing one prototype where we are using two MCU for different task. we are planning to give common reset button (for customer access) for both the MCU using...
Hello,
I am attempting to create an example project of the Asset Tracker using the NRF9160DK.
I have installed SES using the Toolchain Manager.
I have attempted using...
