We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi,
Just wondered about the following ....
Strange parts of this code ... Or things I don't understand
After the first READ in Setup() it successfully reads the data...
I am trying to implement a simple uart echo test using nRF21540 DB board, but I always get NRFX_ERROR_FORBIDDEN when trying to transmit.
This is the initialization code...
I am using nRF5 SDK v16.0.0 on nRF52832. IDE is SES. I am also using FreeRTOS
What order should the following methods be called in? Does it matter when fds_app_init is called...
Hi Team,
I am using SEGGER 5.4 IDE and NRF52840DK controller.
I did not understand the difference between Terminal Emulator and Debug Terminal in Segger IDE.
I am not...
Hi,
I want to configure Timer1 (32 bit ) to run up to 1 sec and then reset. I want this to be done continuously with the help of Short but without using the event handler...
Hello, I have an nRF52811 on a custom board and have been having some issues. I have a nRF52840DK which I used to flash the custom board (while powering the board with the...
I connected it to an external mcu as shown below. After downloading serial lte modem to nrf9160,
at command is sent, but it does not respond. Connect only 3 pins for communication...
Hi I am using the nrf52832 with zephyr os , NCS 1.9.1 , also using the external flash as a secondary slot, using a nor flash I tried to upgrade my app but i an error occurred...
HI, I am trying to develop a project with multiple UART facilities, and I have put the code from the following link in my project.
However, the software UART didn't work...
Dear Nordic community,
I am currently trying to send ADC sensor reading to MQTT broker(hivemq). I have successfully sent some data to the mqtt broker. However, the reading...
Dear all,
I'm trying to build a system with 1 central to 9 peripherals. All devices are based on nRF52832, SDK16, s132 7.0.1.
I've checked this post to get some clues...
Hi, I'm having some trouble with a custom board based on nRF52832.
I need to use NFCPINS (P0.10 and P0.9) as GPIOs. As IDE I'm using Keil uVision.
The code works weel...
Hello! We are having a problem getting the HFXO to start running in the Murata MBN52832 module (nRF52832-based) so that we can start advertising. The 32MHz crystal is embedded...
I'm having trouble reassigning the pin value for the LED's in the connect SDK. I am using the base PWM Blinky example and have changed the pin value assigned to PWM_LED0 in...
Hi Team,
We would like to connect external LEDs to the NRF52840DK controller.
We could not find any unused GPIO pins to connect.
We have referred manual but it showing...
