Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Dear Nordic DevZone community,
we modified the LwM2M client example to fit our application in a LTE-M network. Now we are trying to get GPS to work while still being able...
Hi.
I'm using nrf52832 with SDK-17, and the ESB example (esb_tx and esb_rx)
I'm not much experience in nrf development recently I have a project related to ESB to transmit...
Hello,
In nRF52832, we use nRF Connect to read the board, save the program data into a hex file, and send the file to other developers. They can use nRF Connect to write...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
Would like to interface a SPI ADC – MCP3461 via the nRF52840 serial peripheral interface master with EasyDMA (SPIM). I was not able to find whether or not there is an available...
Hi Everyone,
My issue is mostly stated in the subject, I hope someone can help me recover this DK because as of the moment this is my only way to program/debug out EVT board...
I have nrf52833 as Tx. Ialso have nrf52833+ antenna array as Rx. I want to send CTE data, implement IQ sampling and view AOA for implementing direction finding. Kindly assist...
Hi,
I'm considering shifting to SES (from VS-code) to get debug capabilities.
(Zephyr application developed under NCS tag v1.5.1)
I tried to import my project doing...
Hi
I am developing a Zephyr application on a nRF52840.
Is it possible to runtime change pinmux. Eg. I have set rx/tx for an uart to p1.8, p1.9 and want them to be changed...
Hi nordic,
I want dfu the BL only, how should I pack file? Can show me how to pack instructions of nRF Util, only update bootloader.
Thanks and best regards!
John
Hello,
I am using nrf51822 / SDK v12.3 / SD 130.
I want to change the FW of the sold product to a new FW.
The bootloader address / length of the two are the same,...
