If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
I had my environment running fine with (IIRC) SDK 1.4.x and Segger J-Link v688. I thought "it might help" to upgrade to the latest SDK.
I have the new SDK built and apparently...
Hello Use the S132 Central. Use two S112 peripherals. I want to communicate data to two connected peripheral devices at the same time. You are using nus. The connection was...
Hello,
I am working on a wearable device and need the lowest power consumption possible. The project configuration is:
S132 7.2.0
SDK 17.0.2
The board is powered...
Hi There
My design is basic on nrf52840. I need a pin be controlled alternately by GPIO module and PWM module in my application. The PWM function is realized by setting...
Hello!
I am now working on a customer board based on NINA-B3 module (NRF52840).
I found a weird problem: after successfully flashing firmware through SWD for several...
I was working in a Zephyr project and wanted to test something on my nRF52840-Preview-DK board - which I had just used minutes before and successfully had `west flash` write...
I'm trying to compile the serial LTE modem to trial the functionality.
The version as set by the import examples program in SES does not compile:
The error: mkdir(modules...
I set up PPI so that it kicks off TWIM (I2C) transfer on GPIOTE pin transition low to high. Everything works great, except that I also setup a fork task to set another GPIOTE...
Having a BUS FAULT while trying to use uart_tx on the NRF5340 with NRFConnect SDK. Based on the peripheral_uart sample project. Any ideas what may be causing it?
Heres...
This took me a while to figure out.
The default values for the WDT configuration in SDK 15.3.0 (and 16.0.0) is spelled as "NRFX_WDT_DEAFULT_CONFIG" ?
RMV
The following code has an unexpected out-of-bounds array access:
Primary cause is this line:
On an uninitalized pin number, channel_port_get() returns -1, which...
Firstly my current usecase:
We are using a STM32 as a main processor. the STM uses UART to communicate with the nRF52 using the serialization stuff. I currently have most...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d.
I'm trying to get NVS working using /zephyr/samples/subsys/nvs. It is failing to write. I also tried the code in this post...
hi
i was trying to interface sd card with nrf9160 in segger emstudio. i was following the ticket Reading SD card on nRF9160dk - Nordic Q&A - Nordic DevZone - Nordic DevZone...
HI sir i was trying to interface pdm microphone. i followed the existing ticket PDM Driver for Zephyr on nrf52840 . i had modified the proj.conf as below
but during the...
