I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
I'm trying to develop a small module based around the nrf52832 chip, and I am trying to replicate the reference design and layout as closely as possible. One problem...
Hello,
I am updating my application from older SDK 15.0 to use SDK 17.0.
NRFX_NFCT_ENABLED NRFX_CLOCK_ENABLED are used to enable the files nrfx_nfct.c, nrfx_clock.c respectively...
Hello DevZone,
I am developing a system that has a SoftDevice, UART bootloader, and application. The SoftDevice is S132 SoftDevice v6.1.1. The UART bootloader and application...
RTT seems to be mostly working using the viewer with the command:
JLinkRTTViewer -device nRF52840_xxAA
It seems I need to re-connect each time I start a debug from SES...
Hello Nordic
We are in the process of product development and at the moment we need a chip that transmits stereo audio to any BT headset. That it is possible to control...
I am using nRF52840 as a master to communicate with esp32. For esp32 i am using arduino ide and esp 32 slave library( available in library manager of arduino ide).
For nRF52840...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
Hi, I'm trying to enable the entropy driver so that sys_csrand_get() will stop returning "Entropy reseed error". Does anyone know why it's grayed out? I have tried enabling...
Hi,
I know it's a very common question, but I still haven't fully understood. There is nrf52832 on the peripheral side, there is ble dongle on the central side.
How does...
Hi,
I am trying to get a project to compile using the the segger studio. I have copied one of the example applications and converted it according to your instruction here...
Hello,
I want to add a new driver directly in my project (out of tree), so I've add the differents files, as in the picture below.
When I compile, I get each time...
HI
I used NRF24L01 module in direct mode and chose 250kbps in configuration
In TX mode : whether the data from MCU to module has to be send through exact 250kbps?
Dear Sir
I am trying to work with the ADC .
Attached a code
I get the lines
00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772...
