Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
In the process of testing DFU on the hardware, I am trying to send the DFU Packets through a TTL Cable to a different pins(P0.02, P0.03. No HWFC) instead of sending...
Hi Sir
As subject, I have a nRF52-DK on hand, I'd like to use the "Bluetooth Low Energy APP" of the desktop nRF connect software to scan BLE device and connect it,
Just...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device all based on nRF52840 (Fanstel BT840F module) with nRF5_SDK_for_Thread_and_Zigbee_v4...
Hello,
I am trying edit and compile mcuboot and ultimately upload to the nrf9160.
To do so I am loading the mcuboot project using CmakeLists.txt at v1.2.0\bootloader\mcuboot...
Because the nRF52840 consumes an additional 1mA when QSPI is activated, Nordic has previously recommended deactivating QSPI when not in use, which in practice means deactivating...
Hello DevZone,
Perhip: PCA10040 SDK 15.0.0, SD 6.0.0
Central: PCA10056 SDK 15.0.0, SD 6.0.0
I am working on a BLE project and we need to make sure our link is secured...
Hi,
I am building an application for Thingy:91, currently using SDK 1.3.0. The application is supposed to collect data using BLE and forward it with LTE to the MQTT broker...
Hi,
I wanted to read all the android notification using an embedded BLE device..
I have gone through BLE_ANS example which is in nRF51 SDK, All i want is to implement...
Hi, I'm working with nRF52840DK. I need to run in Direct Test Mode, and to see RSSI & PER. I tried nRF Connect - Direct Test Mode, but it shows only the number of received...
Hi engineers,
I want to transplant demo "usbd_audio" from pca10056 to pca10100, what should I do?
I found a relevant ticket said that
Change board config.
Change...
Hello DevZone,
For a project I'm using the TAG-4 NFC writeable NDEF message example in my SDK and I had a question if this message is always stored in flash or if it is...
I have two nRF5340PDK, both of which would have worked normally. Then I accidentally download the firmware of 52840 version into nRF5340PDK by GProgrammer, which made them...
Hi,
How can I know whether the BLE link between my nrf52840 device and the pc (while connecting via NFC) or the mobile, is configured as a half duplex or a full duplex...
Dear,
I am trying to get secure serial DFU working on our custom board, which is connected to another controller through 2x UART(P0.02, P0.03, P0.30, P0.31) without HWFC...
Hi, I am developing a central application that should get data from a single or even multiple primary services with multiple characteristics in Zephyr. I am using the central_ht...
