Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi everyone,
I have a custom board with a nrf52832 and a I2C device connected to P0.21 (SCL) and P0.20(SDA). I was trying out the twi_scanner example and had modified the...
Hello,
Is there someone who has worked recently with nRF52840 and SHT21 (Humidity / Temperature) sensor ? I have to do some basic test for HW and validate that sensor...
Hi, i would like to work with nrf52832 for my IoT idea. So my question is where do i start from to work with this particular SOC nrf52832 chip? My End product would have integrated...
Dear Madam/Sir,
I'm trying to compile the ble_proximity example on SEGGER Embedded Studio with SDK 12.3.0 and SoftDevice 2.0.1 to run on nRF51822 with PCA10001.
After...
Hey,
I have implemented the ble_hid_mouse example in the nRF52832, and implemented both central multilink and USBD in the nRF52840 dongle so that both boards are paired...
Hi,
We are using nRF52840 in our product for both Client and Server communication on BLE5. We are seeing an overall average time of 5+ seconds for the overall connect, data...
Hello everyone!
I have started to work with openthread recently, and now I have to build a mqttsn client into a stm32 uController. I'm doing that by using the spinel protocol...
Does the nrf52832 has some delay when the shortcut of END_START is enabeled in continuous receiving?What is the meaning of rx chain delay?Does RX chain delay in 2Msps mode...
I'm having problems getting the peer manager to work in a project forked from the ble_app_template on my nRF52-DK (using pca10040e, S112), complaining it can't initialize...
Hi, I am using ble_app_uart_saadc_timer_driven example, which work just fine when receiving data on smartphone (using nRF Connect app). Now I would also like to do the same...
Hi,
I'm using the Nrf52810 with softdevice S112 for the moment.
Question 1:
In ble_gap.h i see that there is a define BLE_GAP_WHITELIST_ADDR_MAX_COUNT (8). Is this realy...
Hi,
I am reading a voltage value from an analog sensor which changes values with 0.02V step. So, i need the accuracy up to 0.02V from ADC channels . But right now i am...
Hi,
I have project based on nRF52840 (using SDK 15.2) and I have a problem with properly adding ADC measurement using scheduler - description as below.
Problem description...
Hi
I want to create this example:
A major network,it include the subnet A and subnet B.
One node X,it belong to subnet A and subnet B.
If the node X was a function...
