Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I have a technical issue I am facing while doing development with Nordic NRF52840. I have an application which I am sending command though virtual com port using CDC ACM USB...
Hello everyone!
I am learning with nrf52840 MCU and SDK version 13. When I read the example. I see one line:
SVCALL(SD_BLE_GAP_CONNECT, uint32_t, sd_ble_gap_connect(ble_gap_addr_t...
Hi,
I'm developing a project based on nRF52 and utilizing NFC for my master's degree. One part of the project will be a beacon with as small PCB layout as possible. That...
Hi,
Often when I try connect BLED112 dongle to bluetooth module BMD-300 by command:
ble_cmd_gap_connect_direct(DeviceMAC, gap_address_type_random, 60, 76, 100, 0); ...
hi,
i want to add uart function to my application. so i added necessary .c files to my project. if i compile the program i am getting these errors.
when i change the...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
Firstly the develop environment.
Windows 10
KEIL as IDE
Device: nrf 51822 - sd s130 2.0.1 - SDK 12.1 nRF5_SDK_12.0.0_12f24da.zip
Use case:
We have 2 application mode...
Hello i am using segger studio i have recently purchased three nrf52dk speically for ble mesh..
i am trying to run examples of mesh alpha sdk that nordiac prvodies but it...
We were playing with renaming some of our test devices to use emoji and other multi-byte utf-8 characters. We have a custom characteristic that allows renaming (since iOS...
dear nordic employee:
I tried to download the project of the ble_app_hrs_c_central by keil(nrf52832)
but It show like the title
I know I should reset the IROM1 and...
Is there a way to get the supervision timeout counter from the peripheral side? I am currently working with nRF5X modules and starting with the nordic uart example from the...
I'm using nRF52832, soft device 2.0, SDK11 and as a central.
When it happens I'm scanning for peripheral to connect. Usually it's a peripheral advertises at very low rate...
Hello,
I'd like to work with my nrf52832 DK while traveling(sins I do that alot recently) and would like to download somehow all of the pages in nordic's info centre to...
