I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi,
I'm trying to follow the MCUBoot + SMP SVR example on this page: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
My application uses NVS to store data and it works just fine - no errors reading or writing , and saved data persists between device power cycles.
My application also has...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Dear Support Team，
1. How to use Bluetooth Low Energy CGM service on NCS? Are there any examples for us to refer to? For example, nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral...
I turn on the device, the led turns green. And I use usb to connect it with computer then I open the nrf connect for desktop, the bluetooth low energy tool,
10:51:05.822...
Hi,
Our custom board using the nRF52840 with SDK 15.0.0 experiences a higher current draw if it starts up without the USBD module enabled at some time. The first screenshot...
Hi, I work with SES on an nrf52840 on a custom board. Here is my issue :
My board can be wakeup from SYSTEM OFF with 2 interrupts on 2 differents GPIOs : 1 is connected...
hello Nordic
sorry to nag but i am waiting for an answer on the thread below for more then a week now, hope you can attend to it or at list inform that you are working...
Hello Devzone,
Working on my Ubuntu 20.04 LTS host, I recently lost ability to flash my nRF9160dk board. The embedded J-Link is detected by its serial number, but an attempt...
Hi, we are working on an application with 300 nodes. each node do 10sec advertsiment and afterwards 10sec scanning pls check the picture below
1) Beacon2 for example advertisies...
Hi,
I have added an external reset switch on my custom board. Maybe a stupid question, but do I need a pull-up resistor? Because in de schematics of the nrf52840 dk I didn...
Hi,
i want to send and receive data via uart1 (connect to a raspberry and send/receive text).
Is there a simple example that shows how to accomplish this?
Im using SDK...
I'm trying to implement a really simple script to sample voltage values from 5 different analog pins on my NRF52832 DK (using Segger at the moment). I found the SAADC example...
While nrfconnect-3.11.0-x86_64.appimage works well, the update to 3.11.1 ends up without Apps.
Ubuntu 18.04
NCS 1.9.1
I found a past case and removed the config and...
