Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
I need to connect a device to an nRF5340 SPI port without creating a custom driver. I'm tempted to use the nrfx_spim driver directly, but I'm trying to do it with Zephyr and...
Hi,
I am migrating from nCS v2.6.1 to v2.9.0, my workspace builds fine on v2.6.1 But on v2.9.0 I am getting the below error:
This is being generated as my main.c has...
Hi
i want to generate security key with the combination of time and private key.can i acheive it in NRF..mainly in NRF52833?
i have a ref code in this repo.. here can...
Hi,
My goal is to primarily save the audio being generated by the Headset device in the LE Audio samples. I have established Bidirectional stream between the Headset and...
I had received a lot of support in: Replacing RS485 link with NRF24L01+ .
At the moment I have 95% proyect working OK but in one operation mode of my program, after some...
it will take about 25uA~ 28uA.
when I remove R18 R19, set io to input with pullup, it will take about 10uA,
&button1 {
gpios = <&gpio0 5 ( GPIO_ACTIVE_LOW | GPIO_PULL_UP...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi Nordic Team I am working on a BLE application using the nRF5 SDK 17.1.0 with Peer Manager configured for Security Mode 1 Level 4 . I am encountering an issue related to...
Hi,
We found a very strange problem when designing a product using nrf5340: The equipment is coated with a layer of UV tri-proof paint on the chip of nRF5340 and the peripheral...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
Hello Folks,
I've got a thorny problem that I've spent an entire day minimizing before even trying to post about it here.
Before diving in, however, here are my environment...
Hello,
I want to utilize two units of nRF7002-DK I have, to evaluate LE bluetooth link between the nRF5340 SoCs. I need access to define CIG and CIS between the two SoCs...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
