Hi Nordic Team,
I am using a matter lock sample code for my application development and modifying a sample lock application for power source cluster support for the matter...
Hello everyone,
I am working on a project that uses the nRF5340 microcontroller and Zephyr.
Initially I took an EVK-NORA-B106 development board that mounts the NORA-B1...
Hello,
In my code, I would like to use the power_down_unused_ram () function. I included the ram_pwrdn.h file but the build returns with undefined reference to `power_down_unused_ram...
Hi,
I am implemented the uart functionality, I'm getting below issue.
[00:00:00.445,526] <err> Throughput: Failed to set UART callback (err -88) [00:00:00.445,556] <err...
I am in the process of bringing up a custom board with an nrf5340 and a FUSB302B USB-C PHY-controller.
As a driver for the FUSB203B, I am using this project as an OOT-module...
My Android app builds and runs fine under Android 13.
But on Android 14 when I try to use the DFU library (ver. 2.5.0) I get the following run-time error: One of RECEIVER_EXPORTED...
Hello Everyone,
I would like to interface the Accelerometer to nrf52810 via TWI pin P0.06 as SCL and pin P0.09 as SDA. I have to read the accelerometer data and send over...
Hi,
We are developing our own board with nrf6190. I already flash the chip with nrf9160dk_at_client_2024-03-13_af2b60d2 application and mfw_nrf9160_1.3.6 modem application...
The customer wants to do wireless approval now, before using the DTM mode, the version available on the old computer is selected, the device can be found on the old computer...
When I click on flash, to flash the blinky program onto the nRF5340 DK board, I get this error message:
FATAL ERROR: required program nrfjprog not found; install it or add...
Hi
I need to send data from nRF7002 to external CPU(STM32) use UART protocol, for HW nRF7002 P0.20 connect STM32 RX and RF7002 P0.22 connect STM32 TX, I try to use exercise...
Hii,
i used nrf5sdk and i am trying to scanning i2c address of Sensirion sgp40 Sensor but unable to sacn i2c address.
I try SGP40 sensor with arduino code its work correctly...
I have tested NPM1300-EK with NRF52840DK and it works.
However, I am using other MCU with NPM1300 but it is a non -zephyr project.
To work with NPM1300, I have tried...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
I have an NRF9161DK 1.0.0 , I was trying to do some wiring but the sensors didn't work, then I noticed that the board delivered 1.7v.
I tried changing it to 3.3v using the...
Hi,
My NRF52840DK ( pca10056 1.1.0 2019.9) would not reset when I press its Reset button. The issue is very similar to https://devzone.nordicsemi.com/f/nordic-q-a/38555...
I have new Thingy 53. Default Edge Inpulse demo works without any problem. But I have problem with Weather Station demo.
First I tested Zigbee version. After flashing using...
Hi,
What is the minimum LDO dropout voltage of nPM1300? For instance, in order to get 3.3V from the LDO, what is the minimum input for the LDO ? On the datasheet there is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...