Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
The broadcast interval is 2s, and the power consumption is 7ua on the DK board; On this basis, the power consumption when using an external low-speed crystal oscillator is...
Hi,
when DC/DC is enabled, current consumption in sleep is higher than when using LDO.
This is consumtion with DCDC = 0
This is power consumtion when DCDC =...
Hi,
I am struggling getting my production programming script to work in a way where I get everything programmed including the App being validated...
For some reason it...
Hi,
I have tried the BLE image transfer demo and I really want to have the similar function about the real time data rate calculation. How could I do that? I found there...
Hi,
We are using nRF52840DK. Our main object is to collect the log for the BLE. We have installed the nRF Sniffer software and wireshark tool to extract the BLE Packets...
Hi,
We are using nrf52840 QFAA with our amplifier that gives ADC values at 100hz. We need to process the data via low pass, band pass filters, median filter, moving average...
Hi, i am using nrf5340 which has flash memory of 1MB. but my application is exceeding this memory size. what I want to do is to merge the image 0 and image and make it as...
Hello everyone I am gradually learning Bluetooth, it takes time, but I need a temporary solution, I need a so-called adapter, Bluetooth <-> UART, to simply transfer bytes...
Hi all,
I develop my own IoT board using NRF52840-QFAA (Rev3), I am follow the Intermediated Course about Creating custom board but some how my board cannot run blinky example...
With a npm1300 I'm able to charge (for instance, the LED showing charging status is on, BCHGCHARGESTATUS is reporting the different steps..... ) but the battery current reporting...
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
Hello,
Our company makes module using nRF52840. And we also make development kit with it.
I recently programmed open bootloader built-in hex in nRF5 SDK v17.1.0 (examples...
nrfConnectSDK V2.8
Toolchain
Board: nrf5340dk
Hi, while compiling ncs-spi-master-slave-example , I am getting below errors
In function 'spi_init': C:/Users/hello...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
Hi,
EDITED: This appears to NOT be related to any open circuit, the SAME behavior comes even with abrupt changes to the current scale, without any interruptions. Additional...
