I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
It appears that after a few seconds and sometimes after a few minutes sleeping threads do not wake up, even though the UART shell and BT NUS are working. The only service...
Hi,
I am trying to configure GPIOs with a custom DTS file, for initial bring-up and testing of the PCBA prior to higher-level development. During compile, I am getting a...
Hi, we have a use case where the central might need to re-bond with our peripheral (e.g., after choosing "Forget this device" in phone settings). I have learned that setting...
Hi
i am working on the nrf5340_dk for making as a controller through the hci_uart build.
can i know the gpio connection mapping on the board?
regards,
Achyuth
Hi, I'm currently having a problem with the uart peripheral.
I have an STM32 MCU connected to the NRF52840. In this case, the NRF acts only as a "transceiver".
Whenever...
I have my own code for handling pin interrupts using the NRF_GPIOTE EVENTS_PORT interrupt. I had some issues with this years ago when I was using the nRF52832 chip, which...
Hi,
is it possible to configure the hci_uart example from NCS in a way that the FICR device address of a nRF52840 is used as public device address? I cloned and compiled...
Hello,
We are trying to get the NVS example on our nrf9160 DK running. The build and the flash process looks fine but the application won't boot. Not even the typical...
Hi,
I bought a second nrf52833-dk. After I program my code on it, I can't debug or read the code because read protection is on. This is strange, because I didn't program...
nRF SDK 17.1.0 I've never touched this example before today, and yet it complains about a bunch of stuff not being found in the file nrf_dfu_validation.c. I am trying to use...
Hi, I try to install nRF connect for VS Code on Ubuntu 20.04 LTS according to the installation guidelines. When I want to set the SDK and toolchain path in the quick setup...
Follow up on: github.com/.../50438
Describe the bug There is a specific case in which the Bluetooth stack seems to become stuck in a state where it will not accept/initiate...
Hi, We are using SDK17 and are implementing the UART y APP_UART_FIFO_INIT. Every now and then we encounter APP_UART_COMMUNICATION_ERROR. I know this is related to buffer overrun...
Hii team,
today i install wireshark version 4.0 and python 3.10 and i downloded nrf sniffer ble software from nordic website and i connected my nrf sdk to pc to flash code...
Hello,
I'm developing an application that will include over the air updates. I read the infocenter information about how the dfu works, with either dual-bank or single-bank...
