Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I have a system that will have multiple ways of doing DFU. BLE, as normal, UART under special circumstances, and a "no transport" way. In the latter I will have transported...
Hi guys,
I was working on my nRF5340 based custom board. From a certain point on the nRF5340 stopped to accept any command from J-Link (SWD link). For example, in response...
I Separate two projects ,SPM application and non-secure application.the spi driver can work in non-secure application,when I try to transplant the spi driver in SPM application...
Hi,
We are using nRF52840 in HV mode and VDD is configured for 1.8v. By mistake, we have connected VDDH to one of the GPIOs as input. What are the implications? How much...
Hi Team,
We are using nrf9160 DK, So we tested the lte_ble_gateway application where we can take the ble data to cloud acting 9160 as gateway. So we also want to perform...
Hi, I'm trying to get the gps driver to work, but the initialization requires getting a device binding. The Asset Tracker project does it like this:
device_get_binding(CONFIG_GPS_DEV_NAME...
<environment> - Windows10 - nrf v1.3.0 - modem v1.2.0 - DK 0.9.0
I get "CLOUD_EVT_ERROR" when using nrf_cloud_agps. There is an error saying "Connection was closed, possibly...
Hello ,
Is there a DFU master code through which one nrf52832 can be updated from another nrf52832. If not please let me know of some useful material to refer to implement...
Hi,
I am using the last up to date demo software for long range BLE throughput test and get systematically, as soon as I press buton 3 or 4 an error "Lost logs - increase...
What are the failure points of a properly developed DFU for OTA updates? On a consumer device where a user may do anything and everything to a device that is executing a DFU...
Hello I have a question, after watching the video: youtu.be/7h4wxyFktkQ It is mentioned that it is not recommended to connect to Google Cloud Platform from a device that is...
Hi, I am running NRF5_SDK_13.0.0_04 and s132_nrf52_4.0.3 on a custom board.
I am getting a Soft Device Fault on an NRF52832 device that I am not able to root cause. This...
Hi,
I downloaded nRF5_SDK_15.3.0_59ac345.
The first time,
Uploaded "..\examples\connectivity\ble_connectivity\hex ble_connectivity_s140_usb_hci_pca10059.hex" by nRF...
So I'm sending multiple payloads of the same width from the transmitter to a receiver and I see it sends only sends 3 times after which `TX_FULL` bit is set in the status...
Hi,
I'm working on a project involving pressure sensors.
These are to be read out via UART and then transmit the data via Mesh to a relay node up to a PC, which visualises...
