Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi all.
Ble does not define the traditional bluetooth SPP service. If i customize the SPP service in ble, can i identify and create a virtual serial port on Windows when...
Sorry this is very basic. Not really for NRF connect for Desktop. But for NRF connect for IOS.
1.I'm just trying to have my iPhone (iphone 6 , IOS 12.4.6) use NRF connect...
I am implementing the BLE buttonless DFU
SDK 14.2,
GCC compiler
softdevice 5.0.0
While writing the firmware data I am getting this error 00> INFO: ../../components...
Hi
I merged the AGPS to serial_lte_modem slm_at_gps.c but it did not work:
1, if I activate LTE in gps_thread_fn(), it will be failed in supl_session();
2, If I activated...
I am trying to read through the nordic 52832 i2c an accelerometer datum lsm303dlhc using the example "twi sensor".
The code used is written below.
Unfortunately, the code...
SDK: 15.1 SoftDevice: S132, v6.1 IDE: Keil Hello I am using the nRF dongle combined with nRF Connect on my PC to connect to my BLE peripheral (custom board). During connected...
Hi there,
I am trying to update the advertising packet (specifically update the battery service value).
I cannot make it work and the function return an error.
Has this...
I want to make serial connection in between an nRF52833 and a LPC1752.
When I use the UART in a firmware without using the SoftDevice for Mesh 4.0.1 , everything is working...
Hi,
I am using a Linux Host to communicate with my nRF52840 as a USB CDC ACM device. As a test, I ran minicom and was able to transfer bytes to my Nordic app successfully...
Gentlemen:
I'm new to Nordic processors, but I have implemented projects with Silabs Gecko and ATTiny processors in the past. I'm working on a project for a consumer product...
Hello,
I have installed Embedded Studio and acquired a Nordic license. However the Tools/Options... nRF Connect menu option does not appear. I tried creating a dummy Nordic...
The project for nRF51822 was developed on base of example ble_peripheral ble_app_hrs for pca10028/s130 with an additional vendor specific service with 128-bit UUID for an...
I have a strange problem. We built 100 custom boards. I've only checked about 50 boards so far. 47 boards work properly. 3 do not.
We used secure_bootloader_uart_pca10056...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
