Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
nRF5 SDK v15.2.0, nRF52840
This issue occurs on reset, most often after cycling power.
There are 4 pages reserved and 4 data pages are found. Since a swap page isn't found...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
Hi,
My current project make use of pairing/bonding and at certain times I change the attribute table. To notify the central device about this change I have added the Service...
I am working on NVMC. I was going through the product specifications for the NVMC. In that, it's given that the number of write operation limit is 181 for a block in nvm....
I'm trying to get the PPK working when connected to aNRF52840-DK, but getting the error - Error while setting up device [REDACTED_SERIAL]: Error occured when close opened...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0 in my customboard.
As peripheral, device communicate Ios phone by using ble.
However, my device sometimes...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
I am working on ble_app_blinky trying to add the capability to transmit data to another device(e.g Arduino).I have already enabled APP_FIFO_ENABLED ,APP_UART_ENABLED and UART0_ENABLED...
How to add uart peripherals to mesh. Thank you very much
How to add uart peripherals to mesh.Thank you very much
How to add uart peripherals to mesh.Thank you very much...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT.
Only PB-GATT is turned on, is the device only sending GATT broadcast packets.
However, I now need to...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT. Now,
I need to make a product. Support PB-ADV. And it is an LPN device. What should I do?
I am using...
Hello,
We are currently evaluating the Bluetooth Mesh solution for our product-line that consists of a Bluetooth Gateway that can communicate with battery-powered devices...
Hi All,
I am using light_control example from Mesh SDK and I need to get something that identify my device in mesh e.g id, address. I would like to send some message to the...
Hi,
This is somewhat tricky question.
In my custom board application program using nRF52832 chip,
I used uart initialization function (e.g. uart_init()) and printf...
