Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
hi,
I am want to communicate with nr52 dongle via serial. The dongle periodically outputs data which I read.
The problem is that is the python connect in the middle...
I'm looking for the set of command line interface for the bluetooth nRF51 sniffer program, such as to list the device available for sniffing. for example the L + . and then...
In the system on low power mode , how and where to change the startup time t1V7 for 1V7 regulator and startup time t1V2 for 1V2 regulator for better power optimization. And...
I know this was asked before, but none of the posts address my problem. There is a similar thread , but the issue on that one was that the softdevice was not being used. I...
Hi all,
I'm implementing a Bootloader with the source code provided no the website (Windows C# app, nRF24LU1 station app and nRF24LE1 device bootloader/app). Everything...
Hello,
When using the nRF Master Control Panel I see other Beacons with "Complete Local Name"... I am building an iBeacon but have not found a way to set the name and have...
The following thread talks about CPU unblocking during connection intervals.
devzone.nordicsemi.com/.../
How does this feature affect BLE Radio Notification? Do...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Good Moring engineers.
I just got nRF24LE . I am wondering the timer2 only provide 2 seconds long period ?
I want my project nRF24LE sleep as long as possible , at less...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
I've just discovered that the Jlink LITE programmer can not program my custom PCB because it runs at 2.7V.
Does the nRF51-DK board support programming an external target...
Hi....
We are working on PCA10028 DK with S130 softdevice version 0.9.0 alpha. Could you tell me about the release of stable SD S130. Hope it will be soon.
Hey,
Is it possible to use the NRF51822 for connectivity together with Arduino, and if so are there any easy instructions as to how to do so? I am looking something on...
Hello I was wondering if I can use both the proprietary protocol 2.4 Ghz ( I understood the one to use for the new projects is Gazell ) and the Blueotooth smart on the nRF51422...
