I am currently in the process of filling out the 18031 RED Cybersecurity certification documentation. I am currently analyzing the security vulnerabilities list of NCS v1...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
working with a nrf52833, soft device 140.
I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
HI,
I am using the NCS V2.9.0 ,nrf Desktop sample;
I want to mouse can pair 3 hosts, and i can select one of them connect and work;
I set CONFIG_BT_MAX_PAIRED=3 and...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
I'm trying to follow the instructions for "nRF51822 Beacon Firmware Documentation" for over the air firmware upgrade of the smart beacon, but I can't find the soft device...
Could this be my problem?
devzone.nordicsemi.com/.../s110-7-0-0-can-i-write-my-own-mbr
an application now starts at 0x15000 which is to make room for an extra 4Kbytes...
Hi,
I am new to BLE Development. Currently I am using NORDIC Development board (SDK Ver 5.2 &Soft device S110). I want to write a small program to establish the connection...
I'm trying to get a handle on the various ways I can implement console output on this system.
I have in the past used the retarget.c/.h code from this forum that uses simple_uart...
Hi
I use the random number generator of LE1,I have made a demo code and the code can generate a random number.As the project in attachment.
I want to get a random time...
Hi all
I get LE1 enter sleep mode(PWRDWN = 0x04;)and use RTC to wake up,but LE1 cann't enter interrupt function after RTC wake up.
If I just use RTC to run ,LE1 can...
Hi,
I am using a custom board with nRF51822 to transmit data. Everything works fine except the transmitting always stop after a while. I am using softdevice 5.2.1. I attach...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
Hello,
I am running a nRF51822 rev G0 with Soft Device 6.0.0 & SDK 5.2.0. My device implements a custom service with 4 characteristics. One of those characteristics is...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
When the central and peripheral is connected, we can get the RSSI value through sd_ble_gap_rssi_start() function. but how can I get the RSSI value when not connected (scaning...
