I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Good morning
I'm new to these SoC systems, but I've developed a custom board with the nRF52810QCAA chip and I'm using the example (ble_app_eddystone) of the SDK15.2. softdevice...
Hello
I am now using nrf52832 and BLE communication with an Android terminal.
BLE communication is a beginner.
I am using nRF_SDK_15.0.0_a53641.
Since I programmed...
It seems possible, but I can't quite figure out how to use nrf_ble_scan_filter_set to use more than one device name. Any assistance? Alternatively, is it possible to use wildcards...
Hi,
In GATT level, on the receiving side - Is it possible to receive a corrupted packet or does the LL identify and discards such packets?
Specifically
- Will host...
Hi
I segger project get compiled and download successfully but it didn't start work. After put it in debug mode, it start working even after removed it from debug mode working...
I am working on a custom board with two MCUs, one nRF52840 and one older MCU.
In the previous iteration of this PCB the old MCU was connected to USB through an FTDI FT232...
Hi,
I've developed a relay application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently...
Hi
My application with SDK11 S132 softdevice is having some unknown issues that will make wdt or hard fault handler happen. And I am trying to use the following code to...
Hello I am using eddystone-beacon example from sdk 12.3 but i am unable to get notification on android phone,nearby setting is also enabled ,please help??
Hello,
I’m looking for an example using the Segger IDE that would read the SAADC and transmit via BLE.
The following example seemed like a good starting place:
...
I am currently working with an nRF51822, SDK 10 (can't be changed), s110. I have a nRf51822-DK (aka pca10028) and wanted to try the d fu_dual_bank_ble_s110_pca10028 example...
I use the nrf_drv_pwm to generate a pwm sequence,
The sequence works fine, but between sequences and at the end I am unable to control the pin.
It is always high unless...
Hi guys
I am looking for export control related information on NRF52832-QFAA-R7, in particular: 1) Is the product a controlled dual use item under EU Regulation 428/2009...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
Hi,
I've been developing an application with the nRF9160 dev kit. We have just received the first rev of our custom hardware with an nRF9160 on it. I am trying to program...
