I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi,
I am facing issue with nrf5340 DK. It is not powering ON properly and not detecting.
When I am trying to power on the DK by connecting USB, the LED5 (PCA10095) on...
I'm trying to get some data written and read from flash memory using the fstorage library as explained in the examples provided with the sdk.
I write to flash and get the...
Hi,
I am still investigating this but, I think it is best that we discuss it on this forum.
I am using SDK 16.0.0, nRF52840, secure_bootloader_usb on a custom board. The...
I just received notification from Onsemi that the ESD protection chip (CM1402-03CP) that I am using between my SIM card connector and nRF91 is obsolete. This is the same chip...
After upgrading nRF Connect SDK to v2.1.0 I noticed that my modified version of connectivity bridge (when running on thingy:91 nrf52840), stops working 30-60 seconds after...
Hi I'm developing a board to isolate external GPIO signals from a Nordic nRF52832 (Isolated input from 5VDC to 25VDC). For this I am using a circuit with the PC817 optoisolator...
Hi, I have similar error on this thread:
I cloned current latest releases of Android-nRF-Toolbox(3.1.3), Android ble library(2.5.1), and Android common library(1.0.27...
Hi everyone,
I'm using an nRF 5340-DK and want to update the application core firmware by using the nRF secure immutable bootloader. The bootloader and the network core...
Hi
I am currently running and adjusting the zephyr echo_bot uart sample on my nrf9160 DK. Currently , the sample makes use of UART0 to send a receive information which I...
I'm trying to connect a Thingy91 to the nRF cloud using just in time provisioning. I'm using MoSh. Here is the error:
mosh:~$ cloud_rest jitp Performing JITP... JITP device...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
