I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I'm using nRF SDK 12.2.0 and the corresponding soft device. I control a I2C slave for which I use the TWI peripheral through the driver implemented in nrf_drv_twi.c. It happens...
Hi,
I trying to enable Hardware Key for mcuboot.
I do the following at mcuboot.conf
CONFIG_BOOT_HW_KEY =y
But I got the following error:
Do I miss something...
Hello, I test SAADC on nRF52810, when I short gound to AIN0, the output is 0 normally, and when I add nothing to Pin I0(AIN0), the output is around 1056(Figure0), however...
I'm using nrf52833 on custom board.
And I need to using RESET pin to GPIO for battery charging detection.
I found CONFIG_GPIO_AS_PINRESET is configuration RESET pin...
Hi,
This may be a basic question. I'm using NRF52840 DK and I'm trying to print some logs from timer callback function, however I havent been successful so far. Here is...
Hi all,
I am using nrf52840 with zephyr
The below link puts device in bootloader mode but with pressing button
I want to do it without pressing button
https://devzone...
Hi All,
I just recently updated to a Mac w/ Apple M1 silicon and am struggling to get my (previously working) scripts to work w/o error.
Specifically, this command/error...
I got an nrf5340-dk development kit. And when I connected it to the computer it was discovered by the computer. But, I could not either connect to it or program it.
I noticed...
Nordic,
We've been using the nRF52832 for many years now. We have a custom board that uses SWCLK and SWDIO to flash our NRF52. We're getting set for production and I am...
I have been developing and debugging this situation for a while. I discovered that the original advice didn't work. First; to get more than 2 client connections going, I had...
Hi teams,
I am testing Direction Finding beacon/scanner pairs with nRF52833 DKs.
With nRFConnect SDK v1.7.1, I started beacon/scanner pair and leave untouched for a few...
Sorry if the title of the post is a bit of a misnomer. I'm currently trying to switch IDEs. Previously I was using Eclipse, but it seems like Nordic completely wants to remove...
Hi! I'm trying out the nRF Connect for VS Code on a M1 Mac, and have a nRF9160-DK connected. The VS Code stuff works fine, I'm able to build sample programs fine, but the...
