I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello,
I try to modify the lpcomp example from the Nordic SDK to trigger the sampling of the lpcomp manually. I have added the following code:
I use AIn3 (GPIO 5) as...
Hello,
I'm using Zephyr SDK. I have got BLE characteristic (my device is a peripheral) with following settings:
After successful write operation, I want to reply with...
Hi,
I'm trying to build the peripheral_lbs sample app for the nRF5340 using VS Code and I cannot get past the build configuration stage. Any assistance would be appreciated...
Hi.
I´m trying to install the application asset_tracker_v2 on my nRF9160DK ver 0.9.0 board.
I´m using VS code and during the build i got errors.
"too few arguments in...
Is there any good tutorial about the Android-BLE-Library Nordic library ?
I have only found the examples, but you need to dig in the code to learn how to use.
Greetings,
What are the settings to allow an nRF52811 to use CODED PHY with the NCS peripheral_hr_coded sample?
NCS v1.7.0
board = ubx_bmd360eval_nrf52811 (effectively...
Hi,
nordic tearm,im use nrf52840 develop a ble hid keyboard,my description of report like this :
my send api like this:
my consumer key like volume add and reduce...
Hello,
In the document about Release assistance indication %RAI. It says
In addition to using the %RAI command, the application must tell when the data connection is...
Hi,
I was using NCS 1.5.0 and Modem firmware 1.2.3.
I have latest DK of nRF9160.
It was running properly without issue specially LTE connection.
But after I migrated...
Hello,
i ran nRF Coap Client and it worked pretty well.
I am working with nRF9160 DK.
Now, I want to add DTLS to this example to secure the data.
Can someone please...
Hi.
I wasn't sure under what topic to post this but it's just a generic question I suppose. I'm still learning so please give it to me in plain English.
It took me a while...
HI Nordic,
As far as I know, in nRF5SDK, the maximum link number of BLE is 20.
I search for the devzone, someone said the number for NCS is 64.
So, I want to know: ...
At multiple places in the SPM subsystem code incorrect assumptions regarding the SRAM memory layout are hard-coded:
At line ~35:
This code is enabled when USE_PARTITION_MANAGER...
