Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Dear Nordic-Support and community,
I am developing a system where a Thingy91 device needs to:
Dynamically connect to a specific BLE device that sends data like Heart...
In version 2.9.0, I modified the JEDEC ID.
The system is supposed to send a "Deep power- down enter(0xB9)" command after reading the JEDEC ID.
However, after the system...
Hi,
I am trying to evaluate the provided smp_svr sample with the BLE DFU on the NRF52840 dongle after I have already tested it on the DK.
I get the following error message...
If we subscribe all attributes of cluster of device connects to coordinator will it make issue? we have noticed its dropping many values if subscribed at same time. if values...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hello all,
I'm working on nRF-9160 and nRF-9151.
What I want to add into SLM application were:
Configure to communicate through UART2 since it will be working with...
Hi,
I'm currently developing a headset application using the nRF5340 AUDIO DK. The thing is, I would require 2 AUDIO DKs (one for headset and one for gateway) to implement...
Hello,
I am wondering if what I am seeing is expected. I tried flashing the modem fw on the nrf9151 using nrfjprog.exe (v10.24.2); which I am able to do successfully, but...
Hello,
I have a Friend SoC with nRF52833 via SPI HCI communicating with my nodes that are nRF52833 MCUs. The nodes are LPN nodes sends data to the friend and awaits a reply...
When using the Serial Monitor, sending AT commands does not show any response from the Actinius Icarus board (nRF9160) Is there any way to resolve or debug this issue further...
Issue Description
The application starts successfully, initializes the modem library, connects to the LTE network, resolves the MQTT broker's address, and establishes an...
Hi,
Just wanted to know if nrf5340dk supports for UART baud rates until 512kbps.? And specific baud rates configuration like 122800.? If yes, is it simply configured as...
Body: Hello, I am using the Nordic Thingy:52 device, but it is not showing up as a port when I connect it to my system. Could you please help me troubleshoot this issue? ...
Hi,
I am using the MDBT42Q module of NRF2832 BLE Module unfortunately i have missed an inductor in my schematics could someone explain me will it work with out the inductor...
~Using nrf Connect sdk and toolchain at version V2.9.0 Attached is the app.zip project.
Basically it consists of a single main funct that prints ("AAAAAAAAAAA") to the...