I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Dear All,
I would like to know information about QDID for nRF5 SDK for Mesh v4.2.0, we are developing costumed equipment using NRF52833 and we need to start the process...
Dear Nordic support team.
Our product nearly complete Rnd stage.
We face only one thing relate to "Cannot reconnect after unpair device with smart phone".
debug wit...
How can i give command from android device to ble board to get the percentage, temperature, or reset or shutdown the device with the help of receiving command from android...
I'm trying to register the SIM card of the 9160 DK at nRF Connect website,
but the website is always showing "still working..." for more than 15 minutes.
Do you have a...
Hello,
I am experimenting with setting up a network via grouping in the following manner.
Bulb_1 will be put into identification mode, and Switch_1 will detect Bulb_1...
Hello,
I am trying to send gps data using MQTT protocol. For this purpose I wanted to combine MQTT simple example with the GPS example. I added all the methods/dependencies...
Hello,
I started to work witn NRF Connect SDK with nrf52840-dk? I mapped lots of peripherals to NRF Connect SDK. There are no problems. However, I try to map nrf_fstorage...
Hello
I am testing out a blinky FreeRTOS example that's a part of the SDK and would like to use SystemView to visualize context switching and tasks. Are there any steps...
Hello,
We're using a BLE connection configured with a 15ms connection interval, and a radio event notification configured to fire 800us prior to a radio event. I'd like...
Hi,
I trying to create a blank Zephyr project for NRF52 and want to use SES. But I could only open pre-existing samples and there's no way to create a blank project.
Appreciate...
I want to create server and client in nrf9160 not through LTE. only transmit on locally in nrf9160
//prj.conf # enable libs CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi support team,
In PS, it stated the sensitivities for ideal BLE transmitter, I would like to know:
o Sensitivity at 1M PHY DLE 255 octets , Dirty Transmitter on
o...
Hi,
In the documentation [1] for 802.11.4 for nrf52-sdk it is mentioned that the documentation is for the nrf52840 soc only. Where can I find documentation regarding 802...
