I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
I would like to confirm that the temperature measurement is sent from the end-device to the coordinator using the example zigbee temperature sensor.
I'm looking at Testing...
With the introduction of mesh_config_file_clear() in 4.2.0 the behaviour of mesh_config_clear() was changed such that only a subset of all the file ids handled by the Mesh...
How to add new i2c based sensor device to ncs\v1.3.0\zephyr\drivers\sensor.
Can you suggest any tutorial to do so as i want to use sensor subsystem which in turn uses i2c...
I have produced ~ 15 different custom board variations that all use the nRF52810-CAAA. They all have the same reference schematic, and use 4 programming pins (V, G, SWDIO...
Hello,
I have an application that uses the SPI- and the TWI-Manager:
But the application throws the error code 17 when the program tries to initialize the TWI-Manager...
Please see Nordic nRF5x Bluetooth DFU upgrade firmware process.
If device is powered off at the step "Copy new firmware" and powered on again device goes into bricked...
I have a peripheral and central that bond with each other. Now until I had peripheral stop advertising on first connection, it was all fine. Now this peripheral needs to connect...
Hi,
On my nRF52840 DK PCA10056 Arduino connector I have mounted some external ST board.
With ST through Arduino interface I am communicating something with nRF52840. ...
Do you know how to handle a write event from its (such as char) descriptor value in a customized BLE service ?
Here is the code of my on_write function :
Setup : nRF52840...
Hello,
I am working with the nrf52832, softdevice s132, and I have configured my own service using this online tutorial :
https://devzone.nordicsemi.com/nordic/short...
hi
im use the command line of nrfutil to ota the nrf52840' firmware.but now i want to develop a soft to ota the device without the environment of python.but i dont kown...
Hello,
I'm measuring the value of a lithium battery (3.7V 110mAh). I used SAADC to measure the battery power and it seems to be quite accurate. The charge IC also attempts...
Hello,
In an older post ( here ) you mentioned that you removed Touchlink examples because they were not of "production quality" and they might not be soon. That was two...
