I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
When I was considering the layout of the nRF5340 chip, I found that the pins of the nRF5340 chip are very small, and I need to punch the vias on the pads, and then use the...
When using the hall or switch button to open the power, the product cannot start. At present, the measured VDD voltage is 3.1V. After pressing the button, the switch control...
I would be happy to read more about the calculations nrfCloud does to derive lat,lon,precision from cells and wifi.
Detailed reason: see thread devzone.nordicsemi.com/....
Hello,
I want to develop a in-app DFU using SPI on nrf5340.
I plan to use dual section with MCUBoot
The app will need to write to secondary partition based on the SPI...
Hey All,
We are working on a product based on the nRF5340. We will be using symmetric key authentication(HMAC) and was wondering the best way to go about provisioning the...
Hi,
in my product I'm using NCS2.5.1 with 20 peripherals on one central. the peripherals have a connection interval of 2 seconds. Lately was trying out the Zephyr BLE Controller...
We have a setup where our product enumerates as 3 com ports.
Is there a way to name each port from the code so they can be uniquely identified via windows?
The problem...
Hi,
I have MCUboot enabled on my application and would like to enable updating the network core as well as the app core through BLE. The network core is just used for BLE...
Hi,
I am currently developing a project using the nRF52810 as my controller, with SEGGER Embedded Studio (version 5.42a) and SDK version 17.0.2 as my development environment...
TLDR: Turn off your antivirus if you have the same error...
Hi everyone,
I'm trying to install nRF Connect v2.6.0, using either: - VS Code + nRF Connect extension (...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
I have bought an nRF52840 to sniff BLE packets. I have followed the user guide v4.1.x to install all SW on Windows 10 : So far I have downloaded nRF Sniffer for Bluetooth...
Hi,
This might be a simple one, but i cannot figure it out.. How do I place the rx/tx/rts/cts lines from UART0 on a GPIO1 pin?
In the piece of DTS below, 'tx-pin' is on...
