Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi
As mentioned in the datasheet, UARTE can operate up to 1Mhz. Is there any special condition/factor to achieve this?
and how fast can a regular GPIO operate?
Thanks...
Computer : Mac Book Air M2
OS : Sonoma 14.5
Hardware : SEEED XIAO nRF52840 Sense
I am building my software using nRF Connect VSCode Extension, while when I select my...
nRF5340 NCS 2.6.1 nrfjprog 10.18.1
My project is based on coap_client and also uses MCUBOOT.
I can program both cores using VS Code, and I notice it splits merged_domains...
Hi,
I am using a nRF9161-DK to flash and debug an external nRF9160 board connected via the nRF9161-DK DEBUG OUT 10-pin connector.
In VS Code "CONNECTED DEVICES", I can...
Hi, I am currently working with the NRF52832 on a custom board that is working with a timer for a particular sleep interval now I have added an external RTC module, and i...
Using nrf9160 with W5500 Ethernet NCS Version 2.6.1
My normal MQTT connection is working fine, but connecting to aws is being an issue. I am getting mqtt -22 error. I...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
I'm working on getting a radio test example project built for our custom board that is currently in production in order to perform some FCC testing, but I'm struggling to...
Hi everyone, this is more of a programming advice question: basically we have a "registration app" associated with our BLE product which will be used to communicate user details...
Hello,
I've been developing code on nRF9160 for a while. In the beginning everything was straight forward and working just fine also the code was pretty simple. Now like...
I am currently working with the nRF5340 and using NAND flash for data storage. With the current code size, I need to create a secondary partition in the external NAND flash...
