You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello,
I'm doing some current measurements on both the Thingy91 and the nRF9160DK and I'm seeing some weird behaviours. My setup is as follows:
First measure on the nRF9160DK...
Hi dear reader
I've read several threads on this issue, but none of them could help resolve my problem.
I've an application which currently is only starting some advertising...
i am using a custom board same as the https://devzone.nordicsemi.com/f/nordic-q-a/29195/nrf52810-custom-board
i edited pca10040e_s112.
it got stuck at sd_ble_gap_ppcp_set...
Battery free BLE solutions are exanpding (wiliot, nexite, atmosic etc). Is there a plan in Nordic to provide a low power chip that will support battery free (or at least ...
Hi, I test the TCP/IP AT command in 9160DK, I download the example Serial LTE modem,
I send the command as below picture.
but it reply as below
==================...
Hello,
Is there any special area where I can save custom MAC address for each device ?
Basically I need to assign unique name and MAC address which the DFU and application...
Hey Forum,
I am using the USB Composite Keyboard example using the standard Descriptor given in the example.
I am able to get all the keys on the Host with a small caveat...
Hi,
I'm trying to use the GNSS application for the nRF9160 to compare GPS antenna performance. There is a Linux utility, GPSMON, that I'm trying to use to display side by...
I use FDS to store some application data. I performing accelerated life testing that randomly power cycles the nRF52840 (on time 4 - 10 seconds) while a central device ( Android...
Hi,
I am trying to run the fat_fs example from zephyr samples on nrf52 development kit (nrf52832) but during building I've got following error :
That's my development...
I am working on UART example and serial port.
I got compile error and modified retarget.c line 99 with
#if defined(__SES_VERSION) && (__SES_VERSION >= 34000) && !defined...
Hi，
I have a circuit board, which is powered by the battery and runs the Bluetooth program. When the power is normally supplied, it runs well. Once the USB charges the battery...
Regarding the capacitive sensor driver with adc for nrf51 series, how am I supposed to wire my board for this to work?
https://infocenter.nordicsemi.com/index.jsp?topic...
I'm trying to follow this how to and unfortunately cannot make it past step one.
https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts...
Hi,
I have a central that uses PM to connect to some peripherals.
If I connect to a peer (connection handle 0), and disconnect this device (e.g. by shutting it off). I...
