Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi
When programming /NordicSDK/v1.3.1/zephyr/samples/basic/blinky in the cpu_app_ns version, it will not start. It is starting when I compile it as a secure application...
In our application we have an RC network (1kOhm-100nF) on pin AIN1. We charge the capacitor with a defined pulse length and then measure the voltage.
At the desired voltage...
Hello,
I can connect to the Segger JLink plus device using USB but when I try to connect to a Segger JLink pro via Ethernet, nrfjprog I receive the following message " There...
Dear Nordic support,
I'd assume it should be OK to allow nrf52840 to advertise in dual phy mode - primary in 1Mbps and secondary coded phy so that phones with and without...
I followed the "Getting Started Assistant" and can import and build the nRF9160 side.
SES -> Open nRF Connect SDK Project:
Works, "Build Solution" works, all seems...
nrfutil version 2.3.0 correctly fails with message " Application file not found." but incorrectly sets the return code to 0
nrfutil settings generate --family NRF52 --application...
I know it basic question but i need direct answer with numbers(exact voltage accuracy)
and i am very much confused to understand about adc output calculation please help...
Hello,
I'm attempting to enter System OFF mode via sleep_mode_enter() using a long press. However, I want to wake up from System OFF using that same button. The problem...
Hi to everyone,
I am having trouble establishing a network connection with NRF9160 Dk. I use a local SIM and according to the information I got from the provider, there...
Hi Nordic
I am using mesh sdk4.1 LPN example to develop a LPN product, we seems found that LPN's RF range will degrade large compared to common mesh node.
We want to try...
hello Nordic
i am working with nrf52840, sdk16, over the peripheral app_ble_blinky example
my system will go to sleep mode for 10 minutes each time, i wonder if there...
SDK: 4.1.0
Hi, I want to send change notification. so I writes below this.
Some buf_id has got failure in zb_zcl_ias_zone_set_status.
So I added loop which get...
Hi,
We are working on a board with nrf5340. We are running the nrf5340 in normal voltage mode. So, we have connected the VDD lines to 3.3V. Since we are using USB signals...
