Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Dear all,
I recently made a custom PCB using the aQFN73 package of the nRF52840 and, even though I respected the antenna constraints (but in 2 layers) I get no signal whatsoever...
Hi Devzone:
I am using P0.00 as SDA and P0.01 as SCL on nRF52833, And I got waveforms like below when I am doing I2C transactions:
the red waveform is SDA and the green...
Hello,
I slightly modified examples\multiprotocol\experimental\ble_zigbee_dynamic_color_light_bulb_thingy so that it can receive changes in the color temperature attribute...
currently i am doing my master Thesis in Bluetooth low Energy. I am searching for BLE Transceiver for Evaluation Purpose. I have a development board S32 from NXP and would...
Hi,
I want to create a Thread border router and am following the instructions from the infocenter.
In the hardware requirements, it is mentioned that the image needs...
Hi Team,
We are using the nrf52830 SOC for our application. In data sheet mentioned that it supports AES-128 bit Hardware engines (ECB,CCM, AAR). How to enable and use these...
Hi guys
I am trying to load a firmware to a Minew's nrf51822 Module using a JLink V8 programmer tool. So far , I can see the chip with the Jlink console:
sudo JLinkExe...
Hi all,
We had implemented Nordic QSPI using "nrf_drv_qspi_write" and "nrf_drv_qspi_read" operation , however I am seeing for page to write in flash of 4096 bytes with 512...
Hi,
During our development, we observed that when BLE central and peripheral devices are communicating, then often central device will not receive data from peripheral device...
mcumgr seems to not like the hex files in mfwnrf9160120.zip, and the NRF programmer can't be plugged into anything automated such as CI, and I'm also running into https:/...
Hi!
This is what I'm using:
-SoftDevice S113 v7.0.1
-SDK v17.0.0.0
-SES v4.52c
-nRF52840
I've created a custom buttonless uart bootloader based on the "secure_bootloader_uart...
So with my NRF52840 board I am trying to use the cc310 backend in zephyr. My project did work until I recently tried to upgrade to ncs v 1.3.0 . The issue was that the build...
Hello, guys!
We are currently developing our firmware with nRF9160-DK and nRF Connect SDK v1.3.0. Among the other things, we need to communicate with the ultrasonic sensor...
I am working in nRF52840 chip with SDK 15.3.0 and softdevice s140. I am looking to automate third party BLE peripheral device, this device is designed to connect with smart...
Hi All,
I have integrated DFU service into my application. I am successfully able to use OAD so far. Today I have added a piece of code to my application. So, my binary...
