It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
We have nRF54H20 with IRONSIDE (SDK3.2.4).
RESET button has default configuration - connected to DEBUG MCU:
We need realize external HW reset of the DK by another...
Hi，
Does it possible to achieve that when inserting a USB into nPM1300, the GPORESET of GPIO3 is triggered to reset the reset port of nRF4L15?
Best regards,
Peter.M...
Enviroment : nRF52833, ncs v3.1.1
The custom board is connected to a DCDC and a 32.768kHz XTAL. However, during the module manufacturing process, the DCDC and XTAL are not...
Tried using the snippet with l2_e1 and got the same bus fault.
nrf Connect SDK v3.4.0
nRF Connect SDK Toolchain v3.4.0
[00:00:00.327,209] <err> os: ***** BUS FAULT ...
I am building a TWI slave with nRF52832.
I am attaching a part of twis_event_handler.
I can read even a 1-byte register value by executing i2c_read_register(SLAVE_ADDR...
Hi Team,
We are planning to use the nRF54LM20 + nRF21540 combination in our new design.
Currently, we are evaluating the band-edge performance on the highest BLE channel...
Hello,
we are seeing a reproducible issue with an external SPI NOR flash on our own custom hardware based on the Nordic nRF52833.
Short summary
The external flash works...
Hello,
My questions is regarding to the modem firmware.
I am planning to ship an IoT product and am questioning wether I should include an external memory for modem FOTA...
Hello, I'm stuck at the build step from teh IoT fundamentals course as when I try to build I get the next error:
It seems that the build needs two (samples/cellular/nrf91_crypto_partitions...
I happened to write some debug log code that broke my Bluetooth. I don't think it should be doing that. When I burrow into the logging, I don't see why this difference is...
We have switched over to the new device tree based partition scheme, and developed custom board files with not-secure variant and mcuboot for ota. OTA was tested using BLE...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
