Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
I am working on developing a program where the nRF52840 dongle is a central device and recognized as an HID keyboard to the computer.
I played around with the peripheral...
I am trying to get a periodic interrupt every 100 uS using TIMER4. My timers_init() code sets up the TIMER4 registers as follows:
My interrupt service routine for now...
Hello
I would like to evaluate the module in a place without Cat-M \ NBIoT support
is it possible (for evaluation purposes) to send the data by other means (for example...
Hi,
New to Nordic, new to SEGGER, and new to ARM, so forgive me if I'm just missing something...
I've been asked to write new code for some boards that have the nRF51822...
I am using the SPIM example in the nRF52840 SDK. It uses SPI_INSTANCE 3. I am doing a simple SPI Write of 2 bytes.
I get SS, SCK, working properly. MOSI is transitioning...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
Hi everyone, I have a custom board using nRF52832 chip.
I want to turn ON and OFF a LED, which is directly connected to a GPIO pin.
Using this configuration I expect...
Hi,
I want to use the math.h for my nRF9160 project, but when I include it, it doesn't find it. I am a beginner and I wanted to ask how do I include libarys proparly in...
Hi,
I have two nRF54840 DK and I am testing ble_app_att_mtu_throughput example with the boards. I am using nRF5_SDK_15.3.0_59ac345 SDK.
The number on the chip is "N52840...
Hello!
Im getting a hardfault when trying to send 10 bytes data via NUS. I receive the data, but the app crashes:
0> <error> hardfault: HARD FAULT at 0x00000000 0...
Hi everybody. I know that it is complete standart question, which has many asks and solutions here. I'm quite new to bootloader management stuff. So asking about some targeting...
